ADVANCED REMOTE CONTROLLED IMMOBILISER
Features of the Eurolock AR250
Back
Kit Component List AR250 Back
Main Component Box
1 x AR250 Owners Manual.
1 x Secret Code Card.
1 x Control Unit in housing with rubber grommet.
2 x Two button Remote controls
1 x 6-Way connector with black wire harness and LED.
1 x 2-Way black connector with black wire harness.
1 x A1 right angle spade terminal with two black wires.
1 x A2 right angle spade terminal with two black wires.
1 x B1 right angle spade terminal with two black wires.
1 x B2 right angle spade terminal with two black wires.
1 x C Circuit external relay connector with black harness.
1 x packet containing 4 screws, 4 plugs and LED holder.
Packaging of Units – AR250 Back
Packaged 1 Unit
Packaged 10 Units
Packaged 20 Units
Owners' Manual Back
MODEL: AR280
ADVANCED REMOTE CONTROLLED IMMOBILISER WITH
VEHICLE RECOVERY SYSTEM
MODEL: AR250 / AR200
ADVANCED REMOTE CONTROLLED IMMOBILISER
INTRODUCTION
Congratulations on your choice of a Eurolock Security System to protect your vehicle. The Eurolock AR280 / AR250 / AR200 is an easy to use system with a wide range of features that provide a high level of security to the driver and vehicle while being convenient to use.
Read the operating instructions carefully to familiarise yourself with the features and operation of the system.
Features of the Eurolock AR280 / AR250 / AR200
Passive arming immobiliser.
3 circuit interruption (AR280 / AR250).
2 circuit interruption (AR200).
LED state indication.
Visual ON/OFF indication via hazard lights (In Vehicle recovery mode if fitted) (AR280).
Audible ON/OFF indication via siren (In Vehicle recovery mode if fitted) (AR280).
"Advanced" remote control.
Up to 6 remote controls.
Unique ID code.
Central locking output facility.
Selective unlocking output facility.
Auto lock if central locking fitted.
Auto unlock if central locking fitted (programmable).
Vehicle recovery system (AR280).
Battery "Low" indicator on remote control.
Remote battery "Low" indicator via system (if siren fitted).
Power down protection.
Secure PIN code, "One" event override.
Secure housing.
Armoured Housing (optional).
Customisation of features.
Remote Control Transmitters
Each unit is supplied with two remote controls. Each remote has two push buttons, which are used to ARM and DISARM the immobiliser.
Press the Red button (closest to the LED).
The LED on the remote will come on and the system will ARM the immobiliser.
Press the Blue button.
The LED on the remote will come on and the system will DISARM the immobiliser. Enter the vehicle and start the vehicle within 30 seconds.
Remote Control Battery "LOW" Indicator
The LED on the remote control will start flashing while pressing a button on the remote control when the battery needs to be replaced. The unit will also respond with the status LED of the vehicle flashing rapidly for 30 seconds to indicate that the remote battery needs to be replaced. Ensure that a new battery is fitted as soon as possible.
Immobiliser
The immobiliser will ARM automatically within 30 seconds after the system is DISARMED if the ignition is not turned ON or the ignition of the vehicle is turned OFF.
The immobiliser LED will flash constantly when the immobiliser is ARMED and will be OFF when the immobiliser is DISARMED. The vehicle can not be started if the immobiliser is ARMED. To DISARM the immobiliser turn the key of the vehicle to the ON position and then press the Blue button of the remote control. The immobiliser LED will now be OFF and the vehicle can be started.
Secret PIN Code and "One" event override
Ensure that you have received your Secret PIN Code card and that the secret 5-digit code is still covered by a scratch removable surface. If the PIN code has been compromised, do not accept the installation that has been done. The secret code is used to add and remove Remote Controls to your system and to start the vehicle in the event a remote control ceases to function. Utilise the ignition key and the LED to key in your secret PIN code to start the vehicle.
1. Procedure for "One" event over-ride
Requires the ignition switch to key in your secret 5-digit code (e.g. 1, 3, 5, 7, 9).
1.1. Vehicle needs to be immobilised (Unable to start) (LED flashing slowly)
1.2. Turn ignition ON. The LED will turn ON continuously (Steady) for 2 seconds and then flash 5 times.
1.3. The LED will turn ON continuously (Steady) for 2 seconds again. During these 2 seconds turn ignition OFF and count 1 LED flash, then turn ignition ON (first digit of 1 entered).
1.4. Turn ignition OFF and count 3 LED flashes again, then turn ignition ON (second digit of 3 entered).
1.5. Turn ignition OFF and count 5 LED flashes again, then turn ignition ON (third digit of 5 entered).
1.6. Turn ignition OFF and count 7 LED flashes again, then turn ignition ON (fourth digit of 7 entered).
1.7. Turn ignition OFF and count 9 LED flashes again, then turn ignition ON (fifth digit of 9 entered).
1.8. Over-ride mode has now been entered, which is confirmed by 5 fast flashes of the LED (1 chirp of the horn, 1 flash of the hazards if fitted with AR280).
1.9. To start the vehicle, turn ignition OFF and then start vehicle as per normal operation. If no action is taken within 30 seconds the immobiliser will ARM and the over-ride procedure will have to be repeated.
1.10. Replace the numbers 1, 3, 5, 7, 9 in the example above with your secret numbers when entering your code.
2. Addition of New remote controls
New remote controls can be added to the system with the secret 5-digit override code, one of the existing Remote Controls and the digits 1 and 4.
2.1. Follow the procedure for "One" event override, procedures 1.1. to 1.8.
2.2. Over-ride mode has now been entered as in procedure 1.8 (confirmed by 5 fast flashes of the LED (1 chirp of the horn, 1 flash of the hazards if fitted with AR280).
2.3. Wait with ignition ON, after 5 seconds the LED will turn ON continuously (Steady) for 2 seconds and then flash 5 times.
2.4. The LED will turn ON continuously (Steady) for 2 seconds again. During these 2 seconds turn ignition OFF and count 1 LED flash, then turn ignition ON (first digit of 1 entered).
2.5. Turn ignition OFF and count 4 LED flashes again, then turn ignition ON (second digit of 4 entered).
2.6. The system will respond with 3 fast flashes of the LED (1 chirp of the horn, 1 Flash of the hazards if fitted with AR280).
2.7. Press one of the current Remote Controls. The system will respond with 5 fast flashes of the LED (2 chirps of the horn, 1 flash of the hazards if fitted with AR280).
2.8. Press the new Remote Control to be added. The system will respond with 3 fast flashes of the LED (3 chirps of the horn, 1 flash of the hazards if fitted with AR280).
2.9. Press the new Remote Control again to confirm. The system will respond with 3 fast flashes of the LED (3 chirps of the horn, 1 flash of the hazards if fitted with AR280).
2.10. Turn ignition OFF to confirm the last setting that was chosen, the system will respond with 2 fast flashes of the LED (2 chirps of the horn, 1 flash of the hazards if fitted with AR280).
2.11. If at any stage of the process no action is taken for more than 10 seconds, then a time-out will occur and no updates will be done, requiring a start from the beginning. The system will respond with 1 flash of the LED (1 chirp of the horn, 1 flash of the hazards if fitted with AR280).
Vehicle Recovery System (AR280 ONLY)
The vehicle recovery system is used to immobilise the vehicle after a car-jacking has occurred.
The vehicle recovery system becomes active after it has been programmed in. Depending on the installation option, the recovery system will be triggered if the driver’s door or any door is opened. To deactivate the recovery system in any phase, press the hidden switch for 1 second.
Phase One (Silent phase)
System triggered: Once the system is triggered the Remote Controls will stop functioning. One minute of silent operation will follow. To deactivate, press the hidden switch for 1 second.
Phase Two (Warning phase)
After the silent phase, 2 chirps of the horn every 5 seconds, repeated 3 times, will warn the driver that the vehicle recovery system has been triggered. To deactivate, press the hidden switch for 1 second.
Phase Three
After the warning phase, the siren and hazard lights will be activated. To deactivate, press the hidden switch for 1 second.
Phase Four
After 15 seconds of the siren and hazard lights being activated the system will start the shut down sequence. The system will ARM the immobiliser within the next minute and therefore cut out the engine. To deactivate, press the hidden switch for 1 second.
Vehicle Recovery System Valet Mode
The vehicle recovery system can be placed in valet mode for vehicle services and valets to ensure that hidden switch location need not be revealed to service and valet centres.
To place in valet mode:
Turn the ignition ON. Press the Blue button of the Remote Control to DISARM the immobiliser. Hold the hidden switch and then press the Remote Control. The system will chirp 3 times and flash once. Release the Remote Control button, but continue to hold the hidden switch for 8 seconds until system chirps 2 times and flashes once.
To remove valet mode:
Turn the ignition ON. Press the Blue button of the Remote Control to DISARM the immobiliser. Hold the hidden switch and then press the Remote Control. The system will chirp 3 times and flash once. Release both the Remote Control button and the hidden switch. After 8 seconds the system will chirp once and flash once.
Central Locking
Central locking can be connected to the vehicle to operate locking and unlocking of doors via remote control. The doors can be locked and unlocked with the ignition ON or OFF. If connected, doors will lock upon starting of the vehicle unless a door is open at the time of starting or if the vehicle is in valet mode.
Custom Features
The following features can be customised at the time of installation of the system:
Vehicle recovery system (AR280).
Immediate vehicle recovery system activation upon starting of the vehicle (AR280).
Doors to unlock when ignition is switched OFF (if central locking fitted).
Doors not to lock when the ignition is turned ON (if central locking fitted).
Selective unlocking of the driver’s door, prior to the other doors (if central locking fitted).
WARRANTY
Goulas Electronics (Pty) Ltd warrants to the final purchaser of the Eurolock Security System, that the product identified on this manual is free from defects in material or workmanship.
This warranty is valid for a period of 24 months from the date of purchase.
Goulas Electronics (Pty) Ltd, at its discretion, will repair or replace the defective product when returned to Goulas Electronics (Pty) Ltd via the installer of the system.
In the event that no satisfaction can be obtained from the installer of the system, only then can the final purchaser approach Goulas Electronics (Pty) Ltd.
Goulas Electronics (Pty) Ltd shall not be responsible for any loss or damage of any nature whatsoever whether direct or indirect, consequential or otherwise, sustained as a result of the use of the product.
Improper use or mishandling of this product by the purchaser will render this warranty null and void.
No warranty claims will be entertained without presentation of invoice or the "Owners Manual" in which this warranty is contained, which has a date, installation centre and signature thereon.
Goulas Electronics (Pty) Ltd will charge the purchaser for services rendered outside the warranty period.
Any implied warranties in respect of this product are expressly excluded.
No agreement whether implied or referred are binding, unless agreed to in writing by Goulas Electronics (Pty) Ltd.
NB: IF THERE ARE ANY QUERIES KINDLY CONTACT YOUR INSTALLATION CENTRE.
Copyright © 2002 by
Micro-Ctrl.
All rights reserved.