INTRODUCTION
Congratulations on your choice of a Eurolock Security
System to protect your vehicle. The Eurolock AR901 / AR601
is a easy to use system with a wide range of features that
provides a high level of security to the driver and vehicle
while being convenient to use.
Read the operating instructions carefully to familiarise
yourself with the features and operation of the system.
Features of the Eurolock AR901 / AR601
Passive arming immobiliser.
3 circuit interruption (AR901).
2 circuit interruption (AR601).
Perimeter alarm protection (doors, boot and bonnet).
Ultrasonic detector.
Isolation of ultrasonic detector.
LED state indication.
"Intelligent" LED indication (alarm diagnostics).
Visual ON/OFF indication via hazard lights.
Audible ON/OFF indication via siren.
"Advanced" remote control.
Up to 6 remote controls.
Unique ID code.
Panic facility.
Central locking output facility.
Selective unlocking output facility.
Auto lock if central locking fitted.
Auto unlock if central locking fitted (programmable).
Vehicle recovery system (programmable).
Ignition tamper protection (hot wire protection).
Battery "Low" indicator on remote control.
Remote battery "Low" indicator via system.
Power down protection.
Dual ultrasonic detector (optional).
Secure PIN code, "One" event override.
Auto arming (programmable).
Secure housing.
Armoured Housing (optional).
Customisation of features.
Remote Control Transmitters
Each unit is supplied with two remote controls. Each
remote has two push buttons, which are used to ARM and
DISARM the alarm and immobiliser.
Press the Red button (closest to the LED).
The LED on the remote will come on and the system will
respond with 2 chirps from the horn and 2 flashes from the
hazard lights of the vehicle. The system is now ARMED.
Press the Blue button.
The LED on the remote will come on and the system will
respond with 1 chirp from the horn and 1 flash from the
hazard lights of the vehicle. The system is now DISARMED.
Enter the vehicle and start the vehicle within 30 seconds.
Remote Control Battery "LOW" Indicator
The LED on the remote control will start flashing while
pressing a button on the remote control when the battery
needs to be replaced. The unit will also respond with 3
chirps from the horn and 1 flash of the hazards after the
normal ARMING (2 chirps from the horn and 2 flashes of the
hazards) or DISARMING (1 chirp from the horn and 1 flash of
the hazards) to indicate that the battery needs to be
replaced. Ensure that a new battery is fitted as soon as
possible. The status LED of the vehicle will flash rapidly
for 30 seconds to indicate that the remote battery needs to
be replaced.
Immobiliser
The immobiliser will ARM automatically within 30 seconds
after the system is DISARMED if the ignition is not turned
ON or the ignition of the vehicle is turned OFF.
The immobiliser LED will flash constantly when the
immobiliser is ARMED and will be OFF when the immobiliser is
DISARMED. The vehicle can not be started if the immobiliser
is ARMED. To DISARM the immobiliser turn the key of the
vehicle to the ON position and then press the Blue button of
the remote control. The immobiliser LED will now be OFF and
the vehicle can be started.
Alarm
The alarm is ARMED / DISARMED by means of the remote
controls. The alarm protects the vehicle from entry via the
doors, boot or bonnet.
Secret PIN Code and "One" event override
Ensure that you have received your Secret PIN Code card
and that the secret 5-digit code is still covered by a
scratch removable surface. If the PIN code has been
compromised, do not accept the installation that has been
done. The secret code is used to add and remove remote
controls to your system and to start the vehicle in the
event a remote control ceases to function. Utilise the
ignition key and the LED to key in your secret PIN code to
start the vehicle.
1. Procedure for "One" event over-ride
Requires the ignition switch to key in your secret
5-digit code (e.g. 1, 3, 5, 7, 9).
1.1. Vehicle needs to be immobilised (No start)
(LED flashing slowly)
1.2. Turn ignition ON. The LED will turn ON
continuously (Steady) for 2 seconds and then flash 5
times.
1.3. The LED will turn ON continuously (Steady)
for 2 seconds again. During these 2 seconds turn
ignition OFF and count 1 LED flash, then turn
ignition ON (first digit of 1 entered).
1.4. Turn ignition OFF and count 3 LED flashes
again, then turn ignition ON (second digit of 3
entered).
1.5. Turn ignition OFF and count 5 LED flashes
again, then turn ignition ON (third digit of 5
entered).
1.6. Turn ignition OFF and count 7 LED flashes
again, then turn ignition ON (fourth digit of 7
entered).
1.7. Turn ignition OFF and count 9 LED flashes
again, then turn ignition ON (fifth digit of 9
entered).
1.8. Over-ride mode has now been entered, which
is confirmed by 1 chirp of the horn, 1 flash of the
hazards and 5 fast flashes of the LED.
1.9. To start the vehicle turn ignition OFF and
then start vehicle as per normal operation. If no
action is taken within 30 seconds the immobiliser
will ARM and the over-ride procedure will have to be
repeated.
1.10. Replace the numbers 1, 3, 5, 7, 9 in the
example above with your secret numbers when entering
your code.
2. Addition of New remote controls
New remote controls can be added to the system with
the secret 5-digit override code, one of the existing
remote controls and the digits 1 and 4.
2.1. Follow the procedure for "One" event
override, procedures 1.1. to 1.8.
2.2. Over-ride mode has now been entered as in
procedure 1.8 (confirmed by 1 chirp, 1 Flash and 5
fast flashes of the LED).
2.3. Wait with ignition ON, after 5 seconds the
LED will turn ON continuously (Steady) for 2 seconds
and then flash 5 times.
2.4. The LED will turn ON continuously (Steady)
for 2 seconds again. During these 2 seconds turn
ignition OFF and count 1 LED flash, then turn
ignition ON (first digit of 1 entered).
2.5. Turn ignition OFF and count 4 LED flashes
again, then turn ignition ON (second digit of 4
entered).
2.6. The system will respond with 1 chirp, 1
Flash and 3 fast flashes of the LED.
2.7. Press one of the current remote controls.
The system will respond with 2 chirps, 1 Flash and 5
fast flashes of the LED.
2.8. Press the new remote control to be added.
The system will respond with 3 chirps, 1 Flash and 3
fast flashes of the LED.
2.9. Press the new remote control again to
confirm. The system will respond with 3 chirps, 1
Flash and 3 fast flashes of the LED.
2.10. Turn ignition OFF to confirm the last
setting that was chosen, the system will respond
with 2 chirps, 1 Flash and 2 fast flashes of the
LED.
2.11. If at any stage of the process no action is
taken for more than 10 seconds, then a time-out will
occur and no updates will be done requiring a start
from the beginning. The system will respond with 1
chirp, 1 Flash and 1 flash of the LED.
Ultrasonic
The ultrasonic sensor if fitted, protects the interior of
the vehicle.
When the system is ARMED by remote control the LED will
start flashing at a faster rate and the ultrasonic sensor
will be set within 15 seconds. Any movement within the
vehicle will trigger the alarm.
To isolate the ultrasonic sensor to allow children or
pets to be left in the vehicle but still arming the doors,
press the Red button for 3 seconds when ARMING the system.
The system will respond as normal (2 chirps of the horn and
2 flashes of the hazards) and will then give another 2
chirps and 2 flashes to indicate that the ultrasonic has
been isolated. The LED will now be Steady ON to indicate
that the system is in the ARMED state but that the
ultrasonic is isolated.
Diagnostics
The system has an "intelligent" LED that indicates the
cause of the alarm being triggered.
When the system is DISARMED and before the vehicle is
started, the LED will flash a number of times every 4
seconds to indicate the cause of the alarm being triggered.
1 flash every 4 seconds - triggered by ultrasonic
2 flashes every 4 seconds - triggered by doors
3 flashes every 4 seconds - triggered by ultrasonic and
doors
4 flashes every 4 seconds - triggered by ignition tamper
5 flashes every 4 seconds - triggered by ultrasonic and
ignition tamper
6 flashes every 4 seconds - triggered by doors and
ignition tamper
7 flashes every 4 seconds - triggered by ultrasonic,
doors and ignition tamper
8 flashes every 4 seconds - triggered by auxiliary input
Diagnostics are cleared when ignition is turned ON or the
system is ARMED again.
Panic
Holding down any of the remote control buttons for 6
seconds will activate the panic facility.
The Panic mode causes the hazards to flash and activates
the siren for 25 seconds without any interruption being
possible. Panic mode can be activated inside or outside the
vehicle with the ignition on or off.
Vehicle Recovery System
The vehicle recovery system is used to immobilise the
vehicle after a car-jacking has occurred.
The vehicle recovery system becomes active after it has
been programmed in. Depending on the installation option,
the recovery system will be triggered if the driver’s door
or any door is opened. To deactivate the recovery system in
any phase, press the hidden switch for 1 second.
Phase One (Silent phase)
System triggered: Once the system is triggered
the remote controls will stop functioning. One
minute of silent operation will follow. To
deactivate, press the hidden switch for 1 second.
Phase Two (Warning phase)
After the silent phase, 2 chirps of the horn
every 5 seconds, repeated 3 times, will warn the
driver that the vehicle recovery system has been
triggered. To deactivate, press the hidden switch
for 1 second.
Phase Three
After the warning phase, the siren and hazard
lights will be activated. To deactivate, press the
hidden switch for 1 second.
Phase Four
After 15 seconds of the siren and hazard lights
being activated the system will start the shut down
sequence. The system will ARM the immobiliser within
the next minute and therefore cut out the engine. To
deactivate, press the hidden switch for 1 second.
Vehicle Recovery System Valet Mode
The vehicle recovery system can be placed in valet mode
for vehicle services and valets to ensure that hidden switch
location need not be revealed to service and valet centres.
To place in valet mode:
Turn the ignition ON. Press the Blue button of the remote
control to DISARM the immobiliser. Hold the hidden switch
and then press the remote control. The system will chirp 3
times and flash once. Release the remote control button, but
continue to hold the hidden switch for 8 seconds until
system chirps 2 times and flashes once.
To remove valet mode:
Turn the ignition ON. Press the Blue button of the remote
control to DISARM the immobiliser. Hold the hidden switch
and then press the remote control. The system will chirp 3
times and flash once. Release both the remote control button
and the hidden switch. After 8 seconds the system will chirp
once and flash once.
Central Locking
Central locking can be connected to the vehicle to
operate locking and unlocking of doors via remote control.
The doors can be locked and unlocked with the ignition ON or
OFF. If connected, doors will lock upon starting of the
vehicle unless a door is open at the time of starting or if
the vehicle is in valet mode.
Custom Features
The following features can be customised at the time of
installation of the system:
Vehicle recovery system.
Chirps removed for silent mode ON/OFF operation.
Immediate vehicle recovery system activation upon
starting of the vehicle.
Doors to unlock when ignition is switched OFF (if
central locking fitted).
Doors not to lock when the ignition is turned ON (if
central locking fitted).
Automatic ARMING of alarm within 30 seconds of
ignition being switched OFF.
Selective unlocking of the driver’s door, prior to
the other doors (if central locking fitted).
WARRANTY
Goulas Electronics (Pty) Ltd warrants to the final
purchaser of the Eurolock Security System, that the product
identified on this manual is free from defects in material
or workmanship.
This warranty is valid for a period of 24 months from the
date of purchase.
Goulas Electronics (Pty) Ltd, at its discretion, will
repair or replace the defective product when returned to
Goulas Electronics (Pty) Ltd via the installer of the
system.
In the event that no satisfaction can be obtained from
the installer of the system, only then can the final
purchaser approach Goulas Electronics (Pty) Ltd.
Goulas Electronics (Pty) Ltd shall not be responsible for
any loss or damage of any nature whatsoever whether direct
or indirect, consequential or otherwise, sustained as a
result of the use of the product.
Improper use or mishandling of this product by the
purchaser will render this warranty null and void.
No warranty claims will be entertained without
presentation of invoice or the "Owners Manual" in which this
warranty is contained, which has a date, installation centre
and signature thereon.
Goulas Electronics (Pty) Ltd will charge the purchaser
for services rendered outside the warranty period.
Any implied warranties in respect of this product are
expressly excluded.
No agreement whether implied or referred are binding,
unless agreed to in writing by Goulas Electronics (Pty) Ltd.
NB: IF THERE ARE ANY QUERIES KINDLY CONTACT YOUR
INSTALLATION CENTRE.
